20 Reasons Why Vinyl Fences Will Never Be Forgotten

How to Install a PVC Fence

There are a few things to be aware of if you're thinking of installing fence. First, you must decide the location where you would like the fence to be erected. Next, you need to prepare the ground. Then, you must place the posts. You may also have to adjust the height of the fence depending on the size of your property.

Preparing the ground

Preparing the ground for the fence is a crucial step in the process. This is crucial because the fence posts must be securely installed. If they aren't, the fence can easily blow over in the wind.

Before you begin digging, you should check your local utility provider to ensure there aren't any underground utilities that could hinder the installation. You can contact 811 to make sure that your yard is marked for underground lines.

A gravel base must be prepared for the fence posts. This will allow water to drain from the posts. It also provides a solid foundation on which blocks will be erected.

Once you have the base, it's time to set up the vinyl fence. The fence should be a minimum of four feet long and 1 inch thick. If you have access to an auger, then you can utilize it to dig holes for fence posts.

Before you start digging, you should get rid of any plants or shrubs that may hinder the digging. In some instances, it is easier to remove the ground before digging it. If you must dig, you will want to avoid digging in sandy or rocky soil.

The next step is to mark the high and low points of your yard. This can be accomplished by using string levels. Attach the string level to stakes about one foot above the ground. The string level serves as a guide for the fence posts.

If your property is located in an extremely dry climate you will probably need to drill pilot holes in advance. This will make the process easier.

It is also necessary to mark the holes. This can be done with markers or spray paint. You can also make use of a mason's sline to ensure that the posts are straight.

You can also fill in the gap using decorative stones. These stones are ideal for small gaps. You will need to find another method of filling the larger gap. It is also possible to put dirt into the gap. This is a low-cost and efficient solution.

The postings are placed in the appropriate places.

The installation of the posts isn't an easy task. First, find the proper place. This can be done by a spirit level, a line mark painted to accommodate the post width or a measuring tool.

Then, put the corner and end posts in place. Also, put in the top and middle rails. You may have to cut some holes. Rails can be used as a spacer between posts.

After you have determined the middle of each hole with stakes or a tape measure then mark the center of the posts with a tape measure. You can also use a string line to help determine the appropriate depth. Once the string line is drawn, tie the ends of the end post to the string. This will ensure the fence will be straight.

After the posts are solidly seated then fill their bottoms up with six inches gravel. This will keep the posts in place and provide drainage.

Make use of a quick-setting concrete for setting fence posts in concrete. This is a type of concrete that is set within three to four minutes. If you are installing a privacy fence, make sure not to overtighten the panels. The panels should sit 22 inches above the ground. The panels is to be secured using #10 1" self-tapping stainless steel screws.

If you are installing a vinyl fence you can join posts to the lower collars using two screws. If you are building privacy fence you should leave one screw on the top rail. You can also cover the horizontal rails at the bottom with duct tape before attaching them to the posts. This will prevent the concrete from seeping into the horizontal rails at the bottom.

Once you are happy with the placement, take off the duct tape. Then, slide the top rail into each of the posts. The pickets can be attached to the rails.

You can also place the rails in the bottom corners. Aluminum u-channel can be used to attach the rails to your posts.

Assembling the panels

It is essential to align the fence posts properly in order to construct a vinyl fence. You may need to use different methods based on the style of your fence. Whether you are installing an oval or square fence, the following steps will get you started.

Before you begin, make sure you have a look at your deed and local zoning laws. Inform neighbors about your plans. If you are installing fence made of vinyl you may need to apply for an building permit.

Once all your posts are set Once all your posts are in place, it's time to install your rail brackets. These screws are connected to the outside of the post. This makes it easier to manipulate of the posts as they are placed.

Before putting up your rail brackets, install the bottom rail. The majority of pre-assembled vinyl panels come with two rails. You might need to modify the rails to match your terrain.

When your bottom rail is installed, you can install the middle rail. You can also install the top rail in the same way. This can be accomplished by using an aluminum uchannel. You can insert it into your posts by making use website of #8 1'' screws.

The pickets then can be installed one at a. Once your pickets have been installed then attach your C channel brackets. You can also put stakes on the corners to keep them in place. You can use cotton string to join the stakes.

Spray paint markers can be used to mark your fence. This will make sure the fence is level once you put it in place.

Additionally, you will need to put in privacy panels. These panels should be erected on the backside your fence. You can also add pea gravel to your holes to keep them in position. If you have a mild slope, you could address it by putting up your fence panels at one end so that they "step down" towards the slope. If the slope is steep, you will need to construct your fence so that it "steps down" from the top to the bottom.

Problems with height changes

It might be difficult to line up the posts if you want to put up fence made of PVC fence. There are two basic ways to do it. One is to lay the posts on the ground and the alternative is to place them in a line. The first method is simpler to implement and ensures that you have concrete under and around the post. The second method requires you to dig out the posts, and then backfill them with dirt.

When digging out the posts, be sure to use a quality backfill and make the holes enough to hold three-quarters of the length of the post. You'll have to dig about six inches in order to place the posts into the base of the gravel. To drill the holes, you may make use of a hole drilling tool. In the last step, hook up the tension bar to the mesh. Then, you can staple the top of the steel mesh into the fence.

If you have problems with lining up the posts or removing the rails from posts that are too high. While this isn't easy but it is feasible to complete the task with two persons. If you own an axe and hammer, you can use them to tack the threads of bolts. This will prevent them from coming out of the fence when you pull it out.